Please enter your contact, our managers will contact you as soon as possible

Retail Wholesale OEM


Products / Outdoor Heating / De-Icing Systems

Heat-Tracing

Design

Section connection

Features

  • Self-limiting heating cable
  • Heat output is automatically adjusted in response to the pipe temperature variation
  • Will not overheat or burn out even in case of overlapping
  • Ready-to-use unit
  • Operating voltage 230 VAC

Description

Froststop Pipe Plug & Play Advanced is the heating section based on double-core heating cable that maintains the required pipe temperature during the whole cold season ensuring its proper and reliable operation.

The heating section consists of a segment of double-core heating cable equipped with 2-meter cold lead with electric plug at one end and with end termination coupling at the other end. For SPC-type heating sections bimetal thermostat is installed in the connection coupling.

The factory made connection and end termination couplings are reliable and tightly sealed.

Advantages

Cost efficiency

The heating section Froststop Pipe Plug & Play Advanced features low power consumption, reliable protection of water supply and sewerage lines against frost and damage, and prevention of condensed moisture creation on the pipe and therefore it extends the service life and reduces repair and operational costs.

Safety

Section Froststop Pipe Plug & Play Advanced uses selflimiting cables as a heating element, thereby the unit will never overheat even in case of the cable overlapping and automatically adjusts the heating temperature in response to the ambient temperature. Due to this feature heating section can be used on a pipe exposed to different temperatures (e.g. with one part installed outdoor and the other inside the house).

Easy installation and power connection

It is easy to install heating section Froststop Pipe Plug & Play Advanced on the pipe. Simply fix the heating tape to the pipe and plug it in the electrical outlet.

Application

Application Installation
Open Area Concrete (Sand embedding)
Roof Under Hot Asphalt (short time)
Gutter & Drain pipe Open (UV resistant)
Freeze Protection    

Ordering information

Technical data

Rated voltage 230 VAC, 50 Hz
Linear output (+10 °C) 12 W/m
Minimum rated fuse size * 10 A
Temperature range **  
 switch on +5 °C
 switch off +15 °C
Maximum operation temperature  
 switched on +65 °C
 switched off +85 °C
Minimum operation temperature –45 °C
Minimum storage temperature –45 °C
Minimum installation temperature –30 °C
Minimum bending radius at installation 25 mm
Cold lead length 2 m
Schuko plug type CEE 7/4
IP protection level IP67

* Circuit breaker type C according to BS EN 60898, 1991
** Only sections with bimetal thermostate (included in the connection of SPC-type)

Product references

Froststop Pipe Plug & Play Advanced with plug

Type Length, m Power, W
SP-HTL-S2-12-2 2 24
SP-HTL-S2-12-4 4 48
SP-HTL-S2-12-5 5 60
SP-HTL-S2-12-6 6 72
SP-HTL-S2-12-8 8 96
SP-HTL-S2-12-10 10 120
SP-HTL-S2-12-12 12 144
SP-HTL-S2-12-15 15 180
SP-HTL-S2-12-18 18 216
SP-HTL-S2-12-25 25 300
SP-HTL-S2-12-30 30 360

Froststop Pipe Plug & Play Advanced with plug & thermostat

Type Length, m Power, W
SPC-HTL-S2-12-2 2 24
SPC-HTL-S2-12-4 4 48
SPC-HTL-S2-12-5 5 60
SPC-HTL-S2-12-6 6 72
SPC-HTL-S2-12-8 8 96
SPC-HTL-S2-12-10 10 120
SPC-HTL-S2-12-12 12 144
SPC-HTL-S2-12-15 15/td> 180
SPC-HTL-S2-12-18 18 216
SPC-HTL-S2-12-25 25 300
SPC-HTL-S2-12-30 30 360

The minimum required fuse size for this application is 10A
Use an automatic circuit breaker «Type C» according BS EN 60 898; 1991